某铁矿隔水护顶矿柱厚度计算及安全影响预测

科学合理地确定矿山隔水护顶矿柱安全厚度是矿山安全生产的前提条件，为保障某铁矿地表民房、道路等建（构）筑物安全，防止矿山开采过程中产生的导水裂隙带贯通第四系含水层，采用荷载传递交汇线法、K.B.鲁别涅依他估算法和冒落带、导水裂隙带高度估算法3种理论分析方法对隔水护顶矿柱厚度进行计算，并利用数值模拟手段对留设隔水护顶矿柱后的开采过程安全影响进行了分析，对理论计算结果进行了验证。3种理论计算方法得出的隔水护顶矿柱厚度分别为14.3～17.3 m、17.5～31.4 m和41.8～57.4 m，推荐隔水护顶矿柱留设厚度为60 m。通过数值模拟分析得出，在留设60 m厚的隔水护顶矿柱的基础上，开采区域和隔水护顶矿柱位置产生的最大拉应力约0.47 MPa，矿山开采不会对隔水护顶矿柱造成破坏；地表产生的最大水平位移约5.8 cm，最大垂直位移约26.5 cm，最大倾斜为1.70 mm/m，最大曲率为0.20 mm/m2，最大水平变形值为0.70 mm/m，满足相关规范要求，预测矿山开采不会造成地表建（构）筑物破坏。     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

Modeling the effect of deep traps on the capacitance–voltage characteristics of p-type Si-doped GaAs Schottky diodes grown on high index GaAs substrates

Numerical simulation, using SILVACO-TCAD, is carried out to explain experimentally observed effects of different types of deep levels on the capacitance–voltage characteristics of p-type Si-doped GaAs Schottky diodes grown on high index GaAs substrates. Two diodes were grown on (311)A and (211)A oriented GaAs substrates using Molecular Beam Epitaxy (MBE). Although, deep levels were observed in both structures, the measured capacitance–voltage characteristics show a negative differential capacitance (NDC) for the (311)A diodes, while the (211)A devices display a usual behaviour. The NDC is related to the nature and spatial distribution of the deep levels, which are characterized by the Deep Level Transient Spectroscopy (DLTS) technique. In the (311)A structure only majority deep levels (hole traps) were observed while both majority and minority deep levels were present in the (211)A diodes. The simulation, which calculates the capacitance–voltage characteristics in the absence and presence of different types of deep levels, agrees well with the experimentally observed behaviour.     

测量二次电子空间分布特征矩阵法的有效性分析

为了准确测量不同材料在实际环境中的二次电子空间分布，设计了一种新型的二次电子发射空间分布测量结构，给出了实验测量原理，用求解特征矩阵的方法对实验结果进行处理，得到了所需的二次电子空间分布。通过模拟计算对该测量方法进行了校验，模拟结果与假设二次电子空间分布函数相吻合，表明该测量方法可靠、测量精度高，为后续样机研制奠定了理论基础。     

某柴油机油底壳仿真计算分析

本文利用ABAQUS结构仿真软件对某发电用柴油机油底壳进行模态、强度计算。在发动机实际运行工况下,油底壳底部为悬空状态,模态计算结果显示油底壳一阶模态距发动机点火激励频率点较近,低于激励频率的1.2倍,模态不满足设计要求;在发动机装配过程中,油底壳底部压在装配台上,发动机在上下方向三倍的重力加速度冲击载荷工况下,油底壳产生的应力最大值低于对应材料的屈服强度极限,强度满足设计要求。通过对油底壳两种状态下的仿真分析,验证和确保了油底壳结构设计的可行性,有效避免了发动机装配和实际运行过程中故障的发生。     

无失效数据机载多余度EWIS可靠性研究

针对高可靠度机载多余度EWIS各组成部分寿命服从指数分布但参数未知的情况，提出采用无失效数据可靠度分析方法评估EWIS的可靠度水平。通过Monte-Carlo仿真方法对连接形式为“先并联、后串联”EWIS各组成部分寿命进行抽样，利用“最小最大值”方法获得系统寿命的抽样值，用概率纸检验法初步判断EWIS寿命是否服从威布尔分布，再用Pearson拟合优度检验法判断EWIS寿命是否服从威布尔分布。结合无故障飞行时间的样本值与EWIS寿命服从威布尔分布的假设，采用无失效数据分析方法评估EWIS的可靠度水平。研究方法对机载多余度EWIS无失效数据可靠度分析有一定的贡献。     

基于GIS单线图的配网停电单模拟操作应用研究

配电网停电会造成电力系统供配电可靠性以及服务质量下降,研究基于地理信息系统(GIS)单线图的配网停电单模拟操作应用。利用网格长度作为基本单位建立坐标系,以选取起始点与终止点为基础,通过四参数法将GIS坐标映射至图纸网格内,实现配网内设备初步布局,将杆塔、站房和整体均匀分布作为优化目标,设置多目标优化目标函数实现GIS单线图最终优化。选取某电力公司配网作为单模拟操作应用对象,模拟结果表明,单模拟操作配网停电后,该配网各负荷点年故障率、次平均停电时间以及年停电时间均有所减少,可有效提升配网的供配电可靠性。     

小型机载激光通信系统设计与验证

针对空空宽带高速通信的需求，设计了小型化机载激光通信系统。仿真分析了300 km、2.5 Gb/s无线激光链路性能，并通过运动仿真台模拟机动环境测试了系统的跟踪与通信性能，其中粗跟踪误差为533.2 μrad(1σ)，精跟踪误差为3.6 μrad(1σ)，测试数据传输240 s，通信误码率为2.82×10-9。仿真与实验验证了该系统用于远距离空空无线激光通信的可行性。     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

Advances in the in vitro digestion and fermentation of polysaccharides

In vitro digestion models are widely used to study the structural changes, digestion and release of food components under simulated gastrointestinal conditions. As compared to the in vivo digestion tests, the in vitro digestion reflects the digestion and utilisation of food after ingestion and has the advantages of being time consuming, inexpensive, reproducible and free from moral and ethical restrictions. This study reviewed the current research studies on the in vitro simulated digestion of polysaccharides conducted in the last 5 years and focused on the oral, gastric and intestinal digestion models, with the aim of providing a basis for the further testing of changes in the content, structure and active ingredients of polysaccharides before and after digestion.